Nitek VR124UTP Bedienungsanleitung PDF herunterladen

Model VR124UTP

UTP Video Router

Installation and

Operation Manual

Introduction

The VR124UTP Video Router is designed to greatly extend the distances to which IP Cameras can operate. The

VR124UTP Video Router consists of two units, a Control Unit and a Remote Unit. The Control Unit is installed at the

NVR/ IP Equipment side and the Remote Unit at the IP Camera side of the installation.

Ground

Connection

FRONT BACK

Note: A sticker on the bottom of each unit identifies whether it is the Control Unit or the Remote Unit.

VR124UTP Video Router Installation Drawing

Install Network to VR124UTP and IP Cameras

Refer to the above diagram when installing. Use best industry practices and follow all local building codes.

1) Connect an earth ground to each unit before making any additional connections.

2) Connect a network cable from the security room or IP network equipment to the CONTROL unit.

3) Connect a twisted pair cable between the CONTROL unit and the REMOTE Unit. Use center terminals of the

RJ11connector.

4) Connect a network cable from the REMOTE unit’s Ethernet jack to the IP camera.

5) Connect a Class 2 power transformer to the push in power connector of each VR124UTP units. The units require

24VAC or VDC @ 1 Amp. There is no polarity to these terminals.

Normal Operation

When power is applied to both units the Network LED’s will come on and the link status LED will blink for about 30 sec-

onds as the link is being optimized. When the link is stable the link status LED will remain “ON”. The data LED will blink

with network activity.

The separate protective earthing terminal provided on this product shall be permanently connected to earth.

NITEK ®

De Schans 19-21 2a

8231 KA Lelystad

Tel: +31(0)320-2300005

Fax: +31(0)320-282186

E-mail: [email protected]

WWW.NITEK.NL

USA

5410 Newport Drive, # 24

Rolling Meadows, IL 60008

Phone: (847) 259-8900

Fax: (847) 259-1300

E-mail: [email protected]

WWW.NITEK.NET

EUROPE

091509 681200103

POWER

10/100

Data

Status

ETHERNET

WIRE PAIR

LINK

Type

Speed Off 10 Mbs

LED Green 100 Mbs

Activity Off No Network

LED On Network Detected

Blinking Network Activity

eed Off 10 Mbs

LED

reen 100 Mbs

Activit

ff No Networ

n Network Detected

Blinkin

Network Activity

Status Blinking Optimizing Link

LED On Link Established

Type On Remote Unit

LED Off Control Unit

NVR

Power

Transformer

VR124UTP

Control Unit

VR124UTP

Remote Unit

5,000 ft (1500 m)

24AWG or Better

Twisted Pair

IP Camera

Network Cable Network Cable

Power

Transformer

Ground

Wire

NITEK

POWER INPUT

12-24 AC/DC, 0-100 Hz

Class 2 only, 1 Amp max.

COMMERCIAL

CCTV PRODUCT

40FE

E325724

1 2

NITEK ® 1
Troubleshooting 2

Inhaltsverzeichnis

Seite 1 - NITEK ®

Model VR124UTP UTP Video Router Installation and Operation Manual Introduction The VR124UTP Video Router is designed to greatly extend the distance

Seite 2 - Troubleshooting

Troubleshooting After completing installation, if the units are not operating properly, check each step at each unit in order. 1) If the Power LED

Kommentare zu diesen Handbüchern

Keine Kommentare

Nitek VR124UTP Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Nitek VR124UTP herunter. Nitek VR124UTP User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Nitek VR124UTP